+45 50 23 22 12    info@let-elektronik.dk | Ring alle hverdage fra 08.00 - 17.00
Dankort + VISA/Dankort VISA Electron MasterCard

Fri fragt
over 300 kr i DK til pakkeshop
60 dages returret
På alle varer
Største udvalg
med over 2500 varer
Dokumentation
På alle varer

Omega2+ Maker Kit

Ingen bedømmelse

This kit includes everything from the Starter Kit as well as the Relay, Servo and OLED Expansion Boards. The collection of electronics components in the Omega2+ Maker Kit includes servos, resistors, LEDs, jumper wires, switches, a 7-segment display, a buzzer and an LCD screen, to name a few. All kit components are nicely packed up in a handy plastic carrying case.

Model/Varenr.: KIT-14541

1.990,60 DKK

Lagerstatus: På fjernlager, bestil før Fredag kl 14 og varen afsendes Tirsdag ugen efter.

Take your IoT development into overdrive with the Omega2+ Maker Kit. Build the same circuits as in the Starter Kit and conduct eight additional experiments using the included Onion Expansion Boards. Experiments include controlling servos, using an H-bridge to control a DC motor, writing text and images to the OLED display, and controlling other high-powered circuits with the Relay Expansion. Step-by-step instructions for building each circuit and running through each experiment can be found in the online Maker Kit Guide under the “Documents” tab.

The Onion Omega parts we carry are separated into three different categories: Mainboard, Dock and Expansion Board. With the parts in this kit you will be able to plug the Omega2+ Board into the Expansion Dock and add any of the included Expansion Boards to your project!

Includes:

  • 1x Onion Omega2+ IoT Computer
  • 1x Expansion Dock for Onion Omega
  • 1x OLED Expansion Board for Onion Omega
  • 1x Servo Expansion Board for Onion Omega
  • 1x Relay Expansion Board for Onion Omega
  • 1x Breadboard
  • 1x Futaba Standard-Sized Servo
  • 1x Generic Sub-Micro-Sized Servo
  • 1x DC Hobby Motor
  • 1x 7-Segment Display (Red LED)
  • 1x LCD Screen (16x2)
  • 1x Shift Register (74HC595)
  • 1x H-Bridge Controller (SN754410)
  • 1x Digital Temperature Sensor
  • 1x Buzzer
  • 5x Slide Switch
  • 12x Tactile Push Button
  • 1x Wall Charger
  • 1x Braided USB Micro-B Cable
  • 20x Multicolor LEDs
  • 5x 100nF Ceramic Capacitor
  • 20x 200? Resistor
  • 10x 1k? Resistor
  • 5x 100? Resistor
  • 5x 470? Resistor
  • 5x 5.1k? Resistor
  • 5x 51k? Resistor
  • 20x Jumper Wire (M/M)
  • 20x Jumper Wire (M/F)

Documents:

Examples:

  • Blinking an LED — Learn the basics of programming the Omega by turning an LED on and off.
  • Blinking Multiple LEDs — Learn some more programming concepts by controlling multiple LEDs at once.
  • Fading an LED — Create a cool LED fading effect using the Pulse Width Modulation (PWM) technique.
  • Reading a Switch — Use a physical switch to control an LED through the Omega.
  • Using a Shift Register — Use a shift register chip to control eight LEDs using only a few GPIOs.
  • Controlling a 7-Segment Display — Add a 7-segment display to the previous circuit to display numbers.
  • Reading a 1-Wire Temperature Sensor — Use a 1-wire temperature sensor to read the ambient temperature.
  • Controlling an LCD Screen — Use the I2C protocol to control an LCD screen attached to the previous circuit.
  • Dimming LEDs — Learn about Pulse Width Modulation and controlling LEDs.
  • Controlling Servos — Use the PWM Expansion to control servos and pick up some Python skills along the way.
  • Run a DC Motor With an H-Bridge — Get really creative and use the PWM Expansion to control an H-Bridge chip, which will in turn drive a DC motor.
  • Writing Text to the Screen — We'll use Python to programmatically write text to the screen.
  • Changing the Screen's Settings — Learn how to use user input to change display settings.
  • Draw Lines — Prompt the user for input and use it to draw lines on the screen.
  • Controlling Isolated Circuits — Learn how to control circuits electrically isolated from the Omega's circuits.

Videos

Kommentarer 0